The best way to install the Access LED Light Strip for Truck Beds # A80312 on a carpet-style BedRug in your 2023 Ford F-150 truck bed is to remove the adhesive backing and stick a hook and loop (or Velcro) type strip on the adhesive. I reached out to my contact at Access who said this is what they do and it has worked out well for them. view full answer...
For your 2012 Dodge Ram 1500 Short Bed truck, I recommend the Truxedo Tonneau Cover # TX547901. Featuring automatic tension control, it rolls up in seconds to store conveniently behind your cab and can be installed in approximately 20 minutes with only a socket and a ratchet. Your chrome bed rails will not be affected as there is plenty of room to install this tonneau and maintain the clearance from your rails. I have included instructions to the proper installation of this product.
You... view full answer...
A spray-in bed liner can be fairly rough, bumpy, which would make it difficult for adhesive to stick to. What I recommend when installing the Access LED truck bed lighting system, # A70380, is to smooth out the area where you want to attach it. If you can flatten out a small area then that will provide more surface area for the adhesive to stick to. view full answer...
The B&W Custom Headache Rack # BWPUCP7502BA does have a louvered design and there is an opening where the 3rd brake light above the cab on your 2020 Ford F-450 Super Duty is going to be visible. Keep in mind, any headache rack will (at least somewhat) obstruct a 3rd brake light camera because of how high they sit up and the area that they have to cover in order to be effective.
This headache rack provides the best solution to avoid any obstruction because of the louvered design and the... view full answer...
I do have a way for you to increase the visibility of your t-load truck bed extender but we currently do not have a set of lights that are designed to work with your setup. Instead, the best option I have for you would be to use a reflector like the Optronics Reflector for Truck or Trailer part # RE52RB.
The reflector measures 4" wide x 1-1/4" tall x 3/8" deep and has an adhesive backing for simple installation. view full answer...
Yes, the B&W Gooseneck Hitch, # BWGNRK1050, will fit on your 1991 Chevrolet K2500 pick up with a 6-1/2 ft bed and 6 lug wheels as long as it does not have a flareside/stepside bed.
The brackets with this hitch do not require any drilling into the truck frame for installation and this hitch is rated for 30,000 lbs. Before towing a gooseneck trailer using this hitch and your truck you should check the towing capacities of your truck. view full answer...
Light bars can sometimes interfere with the installation of the Hopkins Tailgate EasyLift, # 74211. I spoke with my contact at Hopkins to see if they know of any fit issues with a light bar and he told me they did have some reported complaints about light bars interfering on Dodge trucks, but he did not have any information on GM trucks.
I do have some information that will help determine if the EasyLift will fit with your LED light bar. To install the EasyLift on your truck, you will... view full answer...
Yes, even with a low-profile tool box, you will still be able to use the Custom Third Brake Light Camera System - Night Vision - 7" Screen # 3460008.
The # 3460008. camera is adjustable so you can get the view you want, and while the top of the tool box will still be seen, the camera will still be effective for you to view the gooseneck ball or 5th wheel hitch in your Ford's truck bed. view full answer...
LED type lights such as the Access LED Truck Bed Lighting System # A70380 are a great way to add more light to your camper shell or to replace an existing light. LEDs are super-efficient and require very little power, yet they provide fairly bright light output. You can wire this in as a replacement or simply add it to your existing lighting set-up.
The waterproof A70380 includes an adhesive backing for easy press-on installation wherever you need the light. It also has a power switch.... view full answer...
Yes, the Pro Series fifth wheel hitch and rail kit part # PS30128 that you referenced does fit your 1999 Dodge Ram 3500 long bed.
For a 7-way to install in the bed of your truck to make connecting your trailer lights easier you would want the part # 41157. Most 7-ways will be at the rear of the truck near the bumper which doesn't work will with fifth wheel hitches. This kit installs in line with the 7-way at the rear of your truck and gives you a second one to install in the bed. view full answer...
To control your former trucks lights you are going to need the 20 Ft 4-Way Trailer Wiring Harness item # A20WB. This will give you a 4-flat connector that will plug into your tow vehicle and enough wiring to get back to both tail lights.
Depending on whether or not the brake and turn signals are run through different bulbs and wires you might need a converter. The Vehicle to Vehicle Tail Light Converter item # 118158 is what you need if your wires are separate. However, if they are combined... view full answer...
There are several scenarios that could apply for your 2 Chevrolet Trucks. For your 1997 with the 8 ft long bed, part # BWGNRK1000 is the gooseneck hitch that would work well. this applies if the truck is either 1/2 ton, 3/4 ton, or 1 ton.
For the 2000 truck you have, there can be several different options. If it is the 3/4 ton or 1 ton and has the Old Body Style then part # BWGNRK1000 would be a fit. You can tell if you have the Old Body Style or New Body Style quite easily by the tail... view full answer...
The Truck Bed Cargo Camera for Factory Monitor - 3rd Brake Light - Switch Kit # 3460015 will give you 150 degree image with a 360 degree adjustable camera. You will get a view of the top of your tool box, but you will also be able to adjust the view to see the gooseneck ball according to my tech contact at the manufacturer. I've also attached a few videos to assist. view full answer...
Yes, your 2015 Ford F-150 with a light truck camper is absolutely suitable for use with the Brophy Clamp On Camper Tie-Downs # HSAB.
There won't be any issue with your truck's bed and these tie-downs, and the only other thing you'll need are turnbuckles, the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs - 3,000 lbs # TDHP. view full answer...
Unfortunately, the # TLF3004 and # TLF2011 camper tie-downs are for Ford trucks and will not fit your 1988 Chevrolet 1500.
I've linked our selection that is designed for your truck. In order to give you a specific recommendation I'll need to know your truck's bed length, if it has a factory hitch, TorkLight hitch, or another hitch, and if it has a step or board under the truck. view full answer...
If you're referring to using a rearview mirror that has a monitor inside of it then we have two options that will work if you already have a tailgate camera. The Custom Third Brake Light Camera for 4.2" Factory Monitor - Night Vision # 3460002 and the Custom Third Brake Light Camera System w/ Rear View Mirror - Night Vision - 4.3" Screen # 3460005.
If you have a monitor that is compatible with RCA inputs then you can simply use the Custom Third Brake Light Camera for Aftermarket Monitor... view full answer...
The Custom Third Brake Light Camera System w/ Rear View Mirror - Night Vision - 4.3" Screen # 3460005 uses a toggle switch to activate. You won't have it automatically pop up when you put your 2021 Ford F-450 Super Duty in reverse but you will be able to use it whenever you like. For example if you had some cargo in the bed of your truck that you wanted to keep an eye on while going down the road you could activate the toggle switch and see it the entire time you're driving. view full answer...
As long as the bed rails on your truck are not more than 57" from the ground then you could certainly use the Brophy Cable Camper Jacks part # CJ31 to lift the camper shell up from your truck bed. Once lifted, you could just simply drive away and the camper shell will be left standing. This is certainly not the intended purpose of these cable jacks but if it were my camper, I would want two jacks on each side for support. view full answer...
You are correct that a sliding 5th wheel hitch is necessary for short bed applications. A sliding hitch can still be used in a long bed so long as the hitch remains in the forward locked position at all times. This is required to keep the trailer's king pin weight over or slightly forward of the rear axle centerline. If the trailer's tongue weight were any further back than that your head lights could start pointing upward and your rear end sag.
For your current truck, the 1994 Chevrolet... view full answer...
We have what you need in order to wire in your third brake brake light for the truck camper, though there isn't going to be anything specific to either your 2000 Chevy C2500 or your camper shell. You will simply need to add the Pacer Performance 3rd Brake Light Logic Module # PP20-702 and tap into the turn signal circuits of your Chevy. This converter will separate your truck's combined turn signal/brake lights, which you will need to do so your camper shell's brake light will blink along... view full answer...
Go To Results